How to Put Bearings on a Skateboard?

Putting bearings on a skateboard is not difficult,  but there are a few steps to take to make sure you do it properly. Here is a step-by-step guide on how to put bearings on a skateboard:

How to Put Bearings on a Skateboard? Easy Method

Here I will tell you How to Put Bearings on a Skateboard.

Material Required

• A cleaning container  for the bearings
• A dry rag
• Cotton swabs
• Bearing lube
• Skateboard bearings

Instructions

• Using a cleaning container for each bearing, clean out all the old grease and dirt from your bearings. You can do this by adding some water to the container and then swirling the bearings around in it.
• Once you have cleaned out all the old grease and dirt, rinse the bearings off with some clean water.
• Use a dry rag to wipe off any excess water from the bearings.
• Using cotton swabs, apply a thin layer of bearing lube to each bearing.
• Place the bearings on each wheel, making sure that the bearing sits flush against the inside of the wheel.
• Screw on the axle nuts to secure the bearings in place.

KEY STEPS

STEP 1: Get the bearings out of the Skateboard wheels

This is the first step in the process and it is a very important one. You need to make sure that the bearings are out of the skateboard wheels before you start anything else. If they are not, then you will not be able to do anything else and the whole process will be for nothing.

To get the bearings out of the skateboard wheels, you will need to use a bearing extractor tool. You can find this tool at any skate shop or online. Once you have the bearing extractor tool, simply insert it into the center of the wheel and twist it until the bearings come out.

STEP 2: Remove shields

By removing the shields, you will be able to see the inner workings of the bearings. This is important because you need to be able to clean them thoroughly. To remove the shields, you will need to use a bearing press.

A bearing press is a tool that allows you to push the shields out of the bearings without damaging them. You can find this tool at any skate shop or online. Once you have the bearing press, simply insert it into the center of the bearing and push on the shields until they come out.

STEP 3: Place bearings in the cleaning container

A cleaning container may be helpful to place the bearings in as you clean them. This will help to keep them from rolling around and getting lost.

STEP 4: Fill the container with a cleaning solution

You will need to fill the container with a cleaning solution that is designed for bearings. You can find this at any skate shop or online. Once you have the cleaning solution, simply pour it into the container until the bearings are completely covered.

STEP 5: Let bearings soak

You will need to let the bearings soak in the cleaning solution for at least an hour. This will help to loosen any dirt or grime that may be on them.

STEP 6: Lubricate the bearings

Always lubricate the bearings after you have cleaned them. This will help to keep them working properly and prevent them from rusting. To lubricate the bearings, you will need to use a bearing lube. You can find this at any skate shop or online. Once you have the bearing lube, simply apply it to the bearings and then spin them until the lube is evenly distributed.

STEP 1: Reapply shields

Finally, you will need to reapply the shields to the bearings. This will help to protect them from dirt and debris. To reapply the shields, you will need to use a bearing press. You can find this tool at any skate shop or online. Once you have the bearing press, simply insert it into the center of the bearing and push on the shields until they are seated properly.

Some Important Questions:

How do you put bearings on a skateboard?

There are a few different ways to put bearings on a skateboard, but the most common method is to simply press them into the wheel hubs. You can also use a bearing installation tool, which is especially helpful if your bearings are tight-fitting. Once the bearings are in place, you’ll need to screw on the wheels and then tighten the axle nuts to keep everything in place.

How do you put bearings on a skateboard without a press?

There are a few ways to put bearings on a skateboard without using a press. One way is to use two sockets that are the same size as the bearings. Place the bearing on top of one socket, and then use the other socket to tap it into place. Another way is to use a hammer and punch to tap the bearings into place. You can also use a bearing installation tool, which is a simple tool that helps to push the bearings into place. Whichever method you choose, be sure to tap gently so that you don’t damage the bearings.

How do you push skateboard bearings?

You can also use a hammer and punch, or even a drill, but these methods are not as precise and can damage the bearings. To press the bearings into the wheel, you will need a bearing press tool. This is a simple tool that has two plates that fit around the bearing. There is also a handle that is used to push the two plates together, pressing the bearing into the wheel.

How do you put bearings in skateboard wheels without tools?

One way is to simply push the bearings into the wheel using your fingers. Another way is to use a small piece of wood or a metal rod to gently tap the bearings into place. If you have access to a drill, you can also use a drill bit to make a pilot hole for the bearings before tapping them into place. Whichever method you choose, just be careful not to damage the bearings in the process.

How to Clean Bearing Properly?

The most accurate and reliable method to clean a bearing is to use a professional ultrasonic cleaning machine. This will remove all the dirt, grease, and other contaminants from the bearing without damaging it.

If you don’t have access to an ultrasonic cleaner, you can clean your bearings by hand using the following steps:

• Remove the bearings from the skateboard.
• Place the bearings in a bowl of warm water and soap.
• Use a toothbrush or other small brush to scrub the bearings clean.
• Rinse the bearings in clean water.
• Dry the bearings with a clean cloth or air dry them.
• Place the bearings back in the skateboard.

FAQs